Bolton Kit For

Mocal M20 Top Exit Oil Cooler & Remote Filter Relocation Kit For 350z 3.5 Zor5kt

Mocal M20 Top Exit Oil Cooler & Remote Filter Relocation Kit For 350z 3.5 Zor5kt
Mocal M20 Top Exit Oil Cooler & Remote Filter Relocation Kit For 350z 3.5 Zor5kt
Mocal M20 Top Exit Oil Cooler & Remote Filter Relocation Kit For 350z 3.5 Zor5kt
Mocal M20 Top Exit Oil Cooler & Remote Filter Relocation Kit For 350z 3.5 Zor5kt

Mocal M20 Top Exit Oil Cooler & Remote Filter Relocation Kit For 350z 3.5 Zor5kt

GENUINE MOCAL COMBINED OIL COOLER / FILTER RELOCATION KIT. Engines With Metal Spin On Oil Filters Only.

Not suitable for paper element/cartridge oil filters. OIL COOLER KITS AVAILABLE FOR MOST MAKES & MODELS - PLEASE SEE OUR SHOP ITEMS. 10 Row oil cooler m. Top exit oil filter take off plate & seal.

3/4unf remote oil filter head (with mounting bracket). Universal mounting brackets & fixings.

The hose & fittings supplied is designed for self assembly. Once assembled the hoses have a smart/professional appearance. This innovative solution is only achieved by using hose & fittings specially designed for the purpose, therefore is it paramount that the correct Mocal (red band) fittings are used.

Hose clips need to be fitted in between the barbs of the fittings. It is reassuringly hard to fit the fittings to the hose: Dip the hose end in hot water, hold the fitting in a vice, apply WD40 (or similar) to the fitting & hose.

Push the hose over the fitting in one quick action before it cools. Once assembled correctly the hose will have to be cut to remove the fitting.

The kit can be supplied with an extra 1 or 2 meters of hose. FOR ADDITIONAL HOSE / FITTINGS - PLEASE SEE OUR SHOP ITEMS. Rough Guide: A 13 row cooler should be adequate to cool most naturally aspirated engines up to around 150bhp (for track use) given an installation with good airflow, after this a larger cooler will be required.

For road use a 13 row oil cooler is usually adequate for engines up to approx 200bhp in all but extreme conditions, after this a larger cooler will be required. The overall width including mounting brackets is 330mm. Exact cooler size required depends upon: The type of use, ambient temperature, spec of the engine (internal friction, rev range, power etc), airflow through the cooler and over the sump.

If you are using your car for any form of track, competition or high performance use then the engine oil will need cooling. The most common cause of competition / high performance engine failure is loss of oil pressure, as the oil heats up it becomes thinner.

This lowers the pressure produced by the pump and increases the oil escape from the bearings lowering the overall pressure further still. Roughly speaking you need about 10psi of oil pressure per 1000rpm.

7000rpm requires 70psi oil pressure. If the pump cannot meet this demand when the oil is hot/thin engine failure will result - usually in the form of running a crank bearing (death rattle) or throwing a rod through the side of the block! This is especially important on part worn engines - a cooler/thicker oil will give the oil pump a fighting good chance of meeting the demand.

On a new or part worn engine if the oil pressure is maintained, the engine isn't over revved or over heated there is no reason for failure. For track, competition or high performance use a rough target temperature for the oil is around 100°C. Over 100°C the oil thins out rapidly and therefore drops the pressure. Turbo systems will rocket the oil temperature.

An amended invoice will then be sent. (Some fitting tips & tightening torques are included). Questions: We are happy to do our best to answer sensible, genuine questions during our normal office hours (Mon-Fri 09:30-17:30), however please note we do not have intimate knowledge of all makes & models or have personal experience of fitting/using all our products.

Products only fit models stated (if products fit other models its in our favour to say so)! Products listed as universal fitment are not designed for any one model. This item is in the category "Vehicle Parts & Accessories\Car Parts & Accessories\Engine Cooling Components\Engine Oil Coolers & Lines". The seller is "mattyzx" and is located in this country: GB. This item can be shipped worldwide.

  • Outlet Diameter: 5/8bsp
  • Performance Part: Yes
  • Country/Region of Manufacture: United Kingdom
  • Mounting Style: Bolt-On, Bracket Mount, Screw-On
  • End Fitting Type: Female Threaded, Male Barbed Hose Fitting, Male Threaded
  • Material: Rubber, Aluminium
  • Type: Oil Cooler Kit
  • Features: 100% Leak tested, Durability Tested, No Drilling or Modifications Needed for Installation, Single-pass Cooling
  • Manufacturer Part Number: ZOR5KT-M20
  • Finish: Matte, Painted
  • Universal Fitment: Yes
  • Classic Part: No
  • Brand: Mocal
  • Manufacturer Warranty: 1 Year
  • Inlet Diameter: 5/8bsp
  • Items Included: Oil Cooler, Remote Filter Head, Take Off Plate, Hose, Fixing Bolt, Fixing Nut, Mounting Hardware, Seal


Mocal M20 Top Exit Oil Cooler & Remote Filter Relocation Kit For 350z 3.5 Zor5kt